Programming

Quick guides on programming

Quick Guide, Flexlock Invisible/Visible 2.0

Changing mode

To switch functions, you must always proceed via the default setting.

  1. If the lock is not in the default setting, reset to the default setting according to one of the following sections: Reset the lock to the default setting Mode 1 or Programming to the default setting using the mode card.
  2. Program the desired function as described in the section Programming from the default setting Mode 1 to Mode 2, 3, 4 or 5.

 

Programming from the default setting Mode 1 to Mode 2, 3, 4, 5 or Any User Timer.

When programming to a new function (mode) from the default setting, you need the programming card and the mode card for the function you want to program to.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, place the desired mode card over the lock until you hear two beeps in succession as confirmation signal.

Note: In the default setting and Mode 2, users must also be programmed in – see the section Add users.

 

Reset the lock to the default setting Mode 1

To reset, you will need the programming card and service card. Resetting will erase all modes and users.

  1. Hold the programming card over the lock for more than 10 seconds. When the reset beep is heard, any other users will have been erased and the lock is in the default setting.

The lock is now ready to add new users. (See the section Add users.)

 

Programming to the default setting Mode 1 with the mode card

Suitable for companies with a large number of storage units.

When programming from Mode 2, 3, 4, 5 or Any Timer User to the default setting you need the programming card and the mode card for the mode that you are programming from. (If the lock for example is in Mode 5 you will need the Mode 5 card.)

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, hold the mode card for the mode you are programming from over the lock until you hear a beep as confirmation signal.

The lock is now in the default setting and ready to store users (see the section Add users) or for you to program a new mode. Note that you always have to return to the default setting to change between the various configurations.

 

Add users (default setting Mode 1 and Mode 2)

To add users, you need the programming card and the user cards that you want to add. In the default setting and Mode 2, several users can have joint access to the same lock.
These users are programmed into the lock. For Flexlock EM, up to 45 users can be programmed in, and for Flexlock Mifare up to 200 users.

Note that before you add the first user card to a new lock, the service card must be added.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, place the user card over the lock until you hear a beep as confirmation signal.
  3. Repeat for the desired number of users (EM: maximum of 45; Mifare: maximum of 200).

 

Remove users (default setting Mode 1 and Mode 2)

To remove users, you need the programming card and the user cards that you want to remove.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Place the relevant user card over the lock until you hear the erasure signal.
  3. To check that the user card has been removed, wait 5 seconds and then hold he user card over the lock. If everything is correct you will now hear an error signal consisting of 4 rapid beeps.

If instead you want to remove all users that have been added to the lock, see the section Reset the lock to the default setting.

Sound On/Off

If desired, a confirmation signal can accompany opening and closing. The sound on opening/closing is set to Off by default, but it can be programmed to On. To program the sound to On or Off, the programming card and the Sound On/Off card are needed.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, present the Sound On/Off card. When programming to Sound On, you will hear two beeps in succession as confirmation signal. (When programming to Sound Off, no signal is heard, as the successive beeps have been silenced.)

Users will now hear a beep as confirmation signal when they open and close the lock. To turn off the sound, repeat the above procedure.

Ready to use

Ready to Use can be programmed to a lock that is in default setting Mode 1 or Mode 2. For programming to Ready to Use, you need the programming card and the Ready to Use card.

Note: Any service cards that have been added to the lock will not be affected by programming to Ready to Use. The service card will remain in the lock memory and can be used as a master key.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, hold the Ready to Use card over the lock until you hear two beeps in succession as confirmation signal.

Repeat on those locks you want to set up with Ready to Use.

Refresh the lock (program in a new programming card)

To refresh the lock, you need a new programming card and an activation pin. Once refreshed, the lock remains in the same mode as previously. The old programming card is erased and the new one will be valid instead.

Note: Any user and service cards that have been programmed in will also be erased.

  1. Turn the lock over and press the activation pin into the hole on the rear. Hold it pressed in for 1 second until the lock begins to emit repeated beeps that last 7 seconds.
  2. Within the 7 seconds during which the lock beeps, place the new programming card over the lock. You will hear a beep as confirmation signal and the new programming card has now been added.

Diagram of how to refresh your lock to program in a new programming card

Diagram of how to refresh your lock to program in a new programming card

Add a service card

The service card acts as a master key. To add a service card to the lock, you need the programming card and the service card.

  1. Place the programming card over the lock. You will hear a succession of uniform beeps for 7 seconds.
  2. Within 7 seconds, place the service card over the lock until you hear a beep as confirmation signal.

The service card has now been added.